box body

Does anyone know how to safely remove the window trim on the outer part of the door? I really don’t want to tear it up but I’m prepping for paint!

I had the stock engine cover prop off the car for six months and just reinstalled it. But it won't hold the engine cover up...holds it about an inch from being latched. Pretty sure I have it on correctly, there is only one way to bolt it to the fire wall and have the plastic washer over the...

May be you allready know but I took over a last set from Henk Martens and this is how you can fix the bottom fixings. 4 mm (stone) drill and 4 mm rivet, but put an extra washer on it so that it does not pull through the plastic and if the rivet does not completely break off, do not take it...

I want to repaint so that strip has to come off. But is it glued or bolted from inside? And schould it be removed together with the rubber weatherstripping underneath it? En how to remove the two rubber pads at the rear and the front of it? Sorry, i could not find the answer here though there...

X1/9 Firewall Insulation Template After quite a few back and forth photographs, sketches, printouts, markups and redo's, Bob Brown and I have created a set of properly scaled drawings of the firewall insulation. We used the now cleaned and completely stripped Mac X to create the template. The...

so I have had a windscreen sitting here, and it's the last major thing to do. I bought the replacement rubber trim from Midwest, as I never really liked that chrome strip. I have watched about a million videos on people dropping one in. I know an independent glass guy, but meh, $150 right now...

My X has pneumatic door lock actuators from a 1990 VW Passat controlled by a Black Widow. I like pneumatic actuators – they have gentle action and I understand how they work. I installed a separate vacuum pump and pneumatic actuator for the rear trunk latch, controlled by the Black Widow trunk...

I searched high and low on XWEB for a good tutorial on the correct procedure of how to remove the rear chrome trim that outlines the rear window. As I am now getting my car ready for paint (it only took 4 years) I needed to get this trim off and do it without damaging the car or the trim in the...

Though I've been reading this forum for years, this is the first time posting anything and I'm hoping you can help. After seeing the application here several years ago, I decided to go with modified 1968 Camaro bumpers. The modifications are fairly easy and I really like the clean look compared...

I would like a pair of engine cover hinges for a 1500 lid. Let me know what you have. Thanks, Ed

The door on the driver side on my 1984 X sits a little bit low at the rear end when in almost closed position. The slider lifts it up to latch it in correct position, but I must slam the door to close completely. There is no wear or play in the hinges, so this is a matter of adjustment. Are...

I recall some discussions about finding cracks in the center tunnel, around the area of the shift selector. Mine has a couple there also. A few people have made reinforcing plates, but I cannot find examples of them now. Anyone have anything to show, or info about this to share? Here is where...

Really need advice, help in re-mounting the headlight pods into the body. Please see my previous post.

The spring on my targa top latch broke. I found the following items for the repair: Spring. The diameter of the wire is close to the original. The diameter of the spring is a bit bigger, but did not cause and problems: https://www.mcmaster.com/9271K195/ Rivet. M5 x 28mm Aluminum Flat Head...

I want to clean up some paint on the rear of my car. And to make it nice I want to remove the chrome trim piece that goes over the rear buttress I’m pretty sure I just pull it off but it’s pretty snug and before I really get after it I wanted to make sure. And maybe someone has some advice on...

Has anyone successfully fitted a hatchback type strut for the engine cover? If so, what length strut is needed? Part number? The standard loop spring shown in the pics does not allow my cover to open wide enough.

Replacing door from a 79 onto a 82. Is there a procedure for adjusting the hinges ..has a hard time closing, Any advice would be great

I thought I’d start this thread cause I had trouble finding any others. The plan? Swap an early style hood and louvres onto an 82. In my opinion, the look is much cleaner. I’m sure I’ll run into some snags but I think it’ll pay off. Pictures to follow...

I really like most of the things Fiat and Bertone did regarding the X1/9. I even like the way they stuffed the master cylinders into the pedal box for a bigger trunk space. But those flimsy plastic tabs the front spoiler mounts to have got to be one of the silliest things on the car. When I...

The spring on my engine lid isn’t holding the lid up when opened. Any way to adjust this??